GENERATE SCHEMATIC PROTEL 99SE HOW TO
GENERATE SCHEMATIC PROTEL 99SE MANUAL

Q: How can I set up bus-based cabling for the PCB Board drawn in protel? You can directly use the cupl dhl hardware description language to program it. Q: How can I use protel's pld function to compile the gal16v8 program?ДЄnswer: using protel's pld function to compile the gal16v8 program is relatively simple. Q: How can I add Chinese characters to 99se? If there seems to be less Chinese characters after Chinese conversion!

GENERATE SCHEMATIC PROTEL 99SE MANUAL

Q: I used 99se6 to deploy a 4-layer board, which lasted for an hour and 20 minutes to reach 99.6%, but after 11 hours, it only went to 99.9%! You have to stop it.ДЄnswer: for the remaining several net, do a manual pre-cloth, and then the remaining automatic, can reach 100% of the cloth. Q: How do I set the inner electrical layer in pcb multilayer circuit board design? The premise is completely manual layout and wiring. Q: Can a protel pcb diagram output other file formats, such as hyperlynx? This option is not available in the menu.ДЄnswer: Now protel has pcb signal analysis function. We should first change the schematic diagram and follow the rules. Q: How can different net in the pcb be connected together?ДЄnswer: it is better not to do this. You just need to click a check box in the auto-wiring settings. Q: How can I lock the first line before automatic cabling ? One by one?ДЄ: The pre-wiring locking function in 99se is good. Q: Will the Chinese version of protel dxp be available now? Reply: protel dxp was launched later in the second quarter.ДЄ: In the new version of protel, the simulation function will be greatly improved.

Q: What is the latest protel version? When will the new version be launched? Q: Why does the pre-deployed cables of automatic cabling be modified and I think they are not too old? Why is the configuration correct?ДЄnswer: Lock the first line. Reply: Delete the recycle bin to the recycle bin first. After the compilation is successful, you can simulate the file and view the simulation output file. si), and then select the absolute abs option in configure.

GENERATE SCHEMATIC PROTEL 99SE HOW TO

Q: How to Use the pld simulation function of protel 99se?ДЄ: First, you must have a simulation input file (. Is there any reason for protel cabling like this (Electrical)ДЄ: the result of any wiring device is not very beautiful only through automatic cabling. Q: After cabling, some cables are visually too clearly displayed. Q: You can modify the x and y sizes of a pad in the pad attributes.

Q: What should I do if I leave copper dead?ДЄnswer: normally, this type of problem is not encountered.

It takes more than two years, and it has a great leap with protel99se in terms of functionality and scale. Q: Is there any new version available after protel99se?ДЄ: This version is coming soon. However, it is of little use and the video card is good. Q: Can the 3d feature of 99se be improved more? It seems that you can only look at the front! Can the shape be made by yourself?ДЄ: You can use ctrl + to flip a 3d image up, down, left, right-click to flip a certain angle. Q: Is there a good way to set square holes? In addition to drawing on the mechanical layer. Reply: You can add the following content to design -> rules -> clearance constraint: Q: When filling, assuming that the spacing in the wiring rule is 20 mil, but some of my devices require mil spacing, how can I automatically fill in? Q: Can I use the orcad schematic in protel?ДЄnswer: You need to generate the network Table file supported by protel from the orcad schematic, and then open it by protel. It is the same as that of the dual-panel. Protel 99 SE Application Technology Q & A q: Can I use automatic cabling for Multilayer circuit boards?ДЄnswer: Yes.

Generate schematic protel 99se